 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DS1667 Digital Resistor with OP AMP www.dalsemi.com FEATURES Two digitally controlled 256-position potentiometers Serial port provides means for setting and reading both potentiometers Resistors can be connected in series to provide additional resolution Default wiper position on power up is 50% Resistive elements are temperaturecompensated to +20% end to end Two high-gain, wide bandwidth operational amplifiers Low power CMOS design Applications include analog-to-digital and digital-to-analog converters, variable oscillators, and variable gain amplifiers 20-pin DIP package or optional 20-pin SOIC surface mount package Operating temperature range - Commercial: 0C to 70C Resistance values: RESOLUTION -3 dB POINT DS1667-10: 10k 39 ohms 1.1 MHz DS1667-50: 50k 195 ohms 200 kHz DS1667-100: 100k 390 ohms 100 kHz PIN ASSIGNMENT NINV0 INV0 VB W1 H1 L1 RST CLK OUT1 GND 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VCC OUT0 SOUT W0 H0 L0 COUT DQ INVI NINVI 20-Pin DIP (300-mil) and 20-Pin SOIC See Mech. Drawings Section PIN DESCRIPTION VCC GND L0, L1 H0, H1 W0, W1 VB SOUT RST DQ CLK COUT NINV0, NINVI INV0, INVI OUT0, OUT1 - +5-Volt Supply - Ground - Low End of Resistor - High End of Resistor - Wiper End of Resistor - Substrate Bias and OP AMP Negative Supply - Wiper for Stacked Configuration - Serial Port Reset Input - Serial Port Input/Output - Serial Port Clock Input - Cascade Serial Port Output - Noninverting OP AMP Input - Inverting OP AMP Input - OP AMP Outputs DESCRIPTION The DS1667 is a dual-solid state potentiometer that is adjustable by digitally selected resistive elements. Each potentiometer is composed of 256 resistive elements. Between each resistive section of each potentiometer are tap points accessible to the wiper. The position of the wiper on the resistive array is set by an 8-bit register that controls which tap point is connected to the wiper output. Each 8-bit register can be read or written by sending or receiving data bits over a 3-wire serial port. In addition, the resistors can be stacked such that a single potentiometer of 512 sections results. When two separate potentiometers are used, the resolution of the DS1667 is equal to the resistance value divided by 256. When the potentiometers are stacked end to end, the resistance value is doubled while the resolution remains the 1 of 10 032000 DS1667 same. The DS1667 also contains two high gain wide bandwidth operational amplifiers. Each amplifier has both the inverting and non-inverting inputs and the output available for user configuration. The operational amplifiers can be paired with the resistive elements to perform such functions as analog to digital conversion, digital to analog conversion, variable gain amplifiers, and variable oscillators. OPERATION - DIGITAL RESISTOR SECTION The DS1667 contains two potentiometers, each of which has its wiper set by a value contained in an 8-bit register (see Figure 1). Each potentiometer consists of 256 resistors of equal value with tap points between each resistor and at the low end. In addition, the potentiometer can be stacked by connecting them in series such that the high end of potentiometer 0 is connected to the low end of potentiometer 1. When stacking potentiometers, the stack select bit is used to select which potentiometer wiper will appear at the stack multiplexer output (SOUT). A zero written to the stack multiplexer will connect wiper 0 to the SOUT pin. This wiper will determine which of the 256 bottom taps of the stacked potentiometer is selected. When a 1 is written to the stack multiplexer, wiper 1 is selected and one of the upper 256 taps of the stacked potentiometer is presented at the SOUT pin. BLOCK DIAGRAM Figure 1 Information is written to and read from the wiper 0 and wiper 1 registers and the stack select bit via the 17-bit I/O shift register. The I/O shift register is serially loaded by a 3-wire serial port consisting of RST , DQ, and CLK. It is updated by transferring all 17 bits (Figure 2). Data can be entered into the 17-bit shift register only when the RST input is at a high level. While at a high level, the RST function allows serial entry of data via the D/Q pin. The potentiometers always maintain their previous value until RST is taken to a low level, which terminates data transfer. While RST input is low, the DQ and CLK inputs are ignored. 2 of 10 DS1667 Valid data is entered into the I/O shift register while RST is high on the low-to-high transition of the CLK input. Data input on the DQ pin can be changed while the clock input is high or low, but only data meeting the setup requirements will enter the shift register. Data is always entered starting with the value of the stack select bit. The next 8 bits to be entered are those specifying the wiper 1 setting. The MSB of these 8 bits is sent first. The next 8 bits to be entered are those specifying the wiper 0 setting, sent MSB first. The 17th bit to be entered, therefore, will be the least significant bit of the wiper 0 setting. If fewer than 17 bits are entered, the value of the potentiometer settings will result from the number of bits that were entered plus the remaining bits of the old value shifted over by the number of bits sent. If more than 17 bits are sent, only the last 17 bits are left in the shift register. Therefore, sending other than 17 bits can produce indeterminate potentiometer settings. As bits are entered into the shift register, the previous value is shifted out bit by bit on the cascade serial port pin (COUT). By connecting the COUT pin to the DQ pin of a second DS1667, multiple devices can be daisy chained together as shown in Figure 3. When connecting multiple devices, the total number of bits sent is always 17 times the number of DS1667s in the daisy chain. In applications where it is desirable to read the settings of potentiometers, the COUT pin of the last device connected in a daisy chain must be connected back to the DQ input of the first device through a resistor with a value of 1k to 10k. This resistor provides isolation between COUT and DQ when writing to the device (see Figure 3). When reading data, the DQ line is left floating by the reading device. When RST is held low, bit 17 is always present on the COUT pin, which is fed back to the input DQ pin through the resistor (see Figure 4). This data bit can now be read by the reading device. The RST pin is then transitioned high to initiate a data transfer. When the CLK input transitions low to high, bit 17 is loaded into the first position of the I/O shift register and bit 16 becomes present on COUT and DQ. After 17 bits (or 17 times the number of devices for a daisy chain), the data has shifted completely around and back to its original position. When RST is transitioned back low to end data transfer, the value (the same as before the read occurred) is loaded into the wiper 0 and wiper 1 registers and the stack select bit. When power is applied to the DS1667, the device always has the wiper settings at half position and the stack select bit is at 0. 3 of 10 DS1667 WRITING DATA Figure 2 CASCADING MULTIPLE DEVICES Figure 3 READING DATA Figure 4 4 of 10 DS1667 DS1667 LINEARITY MEASUREMENTS An important specification for the DS1667 is linearity, that is, for a given digital input, how close the analog output is to that which is expected. The test circuit used to measure the linearity of the DS1667 is shown in Figure 5. Note that to get an accurate output voltage it is necessary to assure that the output current is 0, in order to negate the effects of wiper impedance RW, which is typically 400 ohms. For any given setting N for the pot, the expected voltage output at SOUT is: VO = -5 + [10 X (N/256)] (in volts) Absolute linearity is a comparison of the actual measured output voltage versus the expected value given by the equation above and is given in terms of an LSB, which is the change in expected output when the digital input is incremented by 1. In this case the LSB is 10/256 or 0.03906 volts. The equation for the absolute linearity of the DS1667 is: VO (actual) - VO (expected) LSB = AL (in LSBs) The specification for absolute linearity of the DS1667 is + 1 LSB typical. Relative linearity is a comparison of the difference of actual output voltages of two successive taps and the difference of the expected output voltages of two successive taps. The expected difference of output voltages is 1 LSB or 0.03906V for the measurement system of Figure 5. Relative linearity is expressed in terms of an LSB and is given by the equation: VO (actual) - LSB LSB = RL The specification for relative linearity of the DS1667 is 0.5 LSB typical. Figure 6 is a plot of absolute linearity (AL) and relative linearity (RL) versus wiper setting for a typical DS1667 at 25C. DESCRIPTION AND OPERATION - OP AMP SECTION The DS1667 contains two operational amplifiers which are ideal for operation from a single 5V supply and ground or from +5V supplies (see Figure 1). An internal resistor divider defines the internal reference of the op amp to be halfway between the power supplies, i.e.: VDD + VB 2 For optimal performance, choose analog ground to be this value. The operational amplifiers feature rail to rail output swing in addition to an input common mode range that includes the positive rail. Performance features include broad band noise immunity as well as voltage gain into realistic loads specified at both 600 ohms and 2k ohms. High voltage gain is produced with low input offset voltage and low offset voltage drift. Current consumption is less than 1.9 mA per amplifier and the device is virtually immune to latchup. 5 of 10 DS1667 LINEARITY MEASUREMENT CONFIGURATION Figure 5 DS1667 ABSOLUTE AND RELATIVE LINEARITY Figure 6 Absolute and Relative Linearity (Normalized to 1 LSB) 6 of 10 DS1667 TIMING DIAGRAM: RESISTOR SECTION Figure 7 7 of 10 DS1667 ABSOLUTE MAXIMUM RATINGS* Voltage on Any Pin Relative to Ground (VB = GND) Voltage on Resistor Pins when VB = -5.5V Voltage on VB Operating Temperature Storage Temperature Soldering Temperature * -0.5V to +7.0V -5.5V to +7.0V -5.5V to GND 0C to 70C -55C to +125C 260C for 10 seconds This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED DC OPERATING CONDITIONS RESISTOR SECTION PARAMETER Positive Supply Voltage Input Logic 1 Input Logic 0 Negative Supply Voltage Resistor Inputs SYMBOL VCC VIH VIL VB L, H, W MIN +4.5 2.0 -0.5 -5.5 VB - 0.5 TYP 5.0 MAX 5.5 VCC+0.5 +0.8 GND VCC+0.5 (0C to 70C) UNITS V V V V V NOTES 1 1 1 1 2 DC ELECTRICAL CHARACTERISTICS RESISTOR SECTION (0C to 70C; VCC = 5.0V 10%, VB = -5.0V 10%) PARAMETER Positive Supply Current Negative Supply Current Input Leakage Wiper Resistance Wiper Current Output Leakage Logic 1 Output @ 2.4 Volts Logic 0 Output @ 0.4 Volts End-to-End Resistor Tolerance Noise (ref: 1V) Absolute Linearity Relative Linearity Resistor Temperature Coefficient SYMBOL ICC IB IU RW IW ILO IOH IOL TOLR N AL RL TCR MIN TYP 3 3 400 -1 -1.0 -20 -120 1.0 0.5 750 MAX 5 5 +1 1000 1 +1 4 +20 UNITS mA mA A ohms mA A mA mA % dB Hz NOTES -1 9 LSB LSB ppm C CAPACITANCE PARAMETER Input Capacitance Output Capacitance SYMBOL CIN COUT MIN TYP MAX 5 7 (TA = 25C) UNITS pF pF NOTES 8 of 10 DS1667 AC ELECTRICAL CHARACTERISTICS RESISTOR SECTION PARAMETER CLK Frequency Width of CLK Pulse Data Setup Time Data Hold Time Propagation Delay Time Low to High Level Clock to Output RST High to Clock Input High RST Low from Clock Input High SYMBOL fCLK tW tSU tH tPLH tHHT tHLT MIN 50 30 10 (0C to 70C, VCC = 5V 10%) TYP MAX 10 UNITS MHz ns ns ns ns ns ns NOTES 50 50 50 3 OPERATIONAL AMPLIFIER SECTION DC ELECTRICAL CHARACTERISTICS (0C to 70C; VCC = 5.0V 10%, VB = -5.0V 10%) PARAMETER Input Offset Voltage Input Offset Voltage Drift Common Mode Rejection Positive Power Supply Rejection Negative Power Supply Rejection Input Common Mode Voltage Range Large Signal Voltage Gain Large Signal Voltage Gain Output Swing Output Swing Output Swing Output Swing Output Current Output Current SYMBOL VOS VOSD CMR +PSR -PSR CCCM VB+1.5V 106 96 4.7 -4.7 4.5 4.6 -4.6 13 13 58 63 -4.5 -4.6 MIN TYP 5 10 62 62 62 VCC MAX 10 UNITS mV uV/C dB dB dB V dB dB V V V V mA mA RL=2k RL=600k NOTES VSWGH VSWGL VSWGH VSWGL VO,SOURCE VO,SINK 4.6 RL=2k to GND VB = -5V RL=600k to GND VB = -5V VO = 0V VO = +5V 9 of 10 DS1667 OPERATIONAL AMPLIFIER SECTION AC ELECTRICAL CHARACTERISTICS PARAMETER Slew Rate Gain Bandwidth Product Phase Margin Gain Margin Amp-to-Amp Isolation Input Referred Voltage Noise Input Referred Current Noise Total Harmonic Distortion SYMBOL VSL GBP PM GM AAI IRVF IRV1 HD MIN 0.7 (0C to 70C; VCC = 5.0V 10%) TYP 2 2.5 75 20 130 100 0.0002 0.1 MAX UNITS V/s MHz deg dB dB nV/ Hz pA/ Hz % NOTES 6 5 5 5 F=1 kHz F=1 kHz F=10 kHz AV=-10 RL=2k VO = 1VPP NOTES: 1. All voltages are referenced to ground. 2. Resistor inputs cannot exceed the substrate bias voltage in the negative direction. 3. Measured with a load as shown in Figure 8. 4. Over a frequency range of 0 - 1 kHz. 5. Load is RL = 600 CL = 10 pF. 6. VDD = +5.0V VB = -5.0V connected as voltage follower with 10V step input and RL = . 7. To achieve best op amp performance, VDD = +5.0V VB = -5.0V and analog ground = 0V. In general analog ground = VDD + VB 2 . 8. OP AMPS idle, no load. 9. Valid at 25C only. LOAD SCHEMATIC Figure 8 10 of 10 |
Price & Availability of DS1667
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |